RT-AC86U 384.16 Hi, I updated to the latest Merlin firmware this morning (about 9 am) and since doing so my NE CRC count has gone up to 326598 over 5 hours. ...

[UK Sentinel]

That is strange because @Bully is exact opposite to yours as his actual Synch speed/rate and Real Synch speed/rate have both increased whilst he has been using a Broadcom, modem,

 

HG612 Modem Stats (Broadcom)

Max: Upstream rate = 12136 Kbps, Downstream rate = 50748 Kbps
Bearer: 0, Upstream rate = 12097 Kbps, Downstream rate = 39709 Kbps

 

DrayTek Vigor Stats (Lantiq)

———————- ATU-R Info (hw: annex A, f/w: annex A/B/C) ———–
Running Mode            :      17A       State                : SHOWTIME
DS Actual Rate          : 35000000 bps   US Actual Rate       : 10760000 bps
DS Attainable Rate      : 44789800 bps   US Attainable Rate   : 10862952 bps

In a completely sane world, madness is the only freedom (J.G.Ballard).

You need to login in order to vote

[Mrk26]

Yes, I see these and actually broadcom based modem improve on @Bully line where on mine this time cause more bad than good. I usually use broadcom modem to mantain line from interleave to fastpath, as you know. What happens yesterday, no idea, one of these bad memories which I would kike to erase from my memory 😜

You need to login in order to vote

[UK Sentinel]

Mrk26 wrote:

Yes, I see these and actually broadcom based modem improve on @Bully line where on mine this time cause more bad than good. I usually use broadcom modem to mantain line from interleave to fastpath, as you know. What happens yesterday, no idea, one of these bad memories which I would kike to erase from my memory 😜

(tech)

In a completely sane world, madness is the only freedom (J.G.Ballard).

You need to login in order to vote

[UK Sentinel]

Bully wrote:

Is the Below WAN setup correct?

See my WAN settings for comparison, only differences is (mine are all default)  my Bridge Type is IP_Bridged and you have 802.1p enabled and I do not .

I think your Bridge Type should change if your are having problems  but not so sure regarding 802.1p as that is QoS and unsure if you have set this up. ?

 

Mine seems to work well and no complaints from family as yet

 

 

Attachments:

1. 

   modem.png
   

In a completely sane world, madness is the only freedom (J.G.Ballard).

You need to login in order to vote

[Bully]

Today’s Stats –

xdslcmd info –stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 6
Last initialization procedure status: 0
Max: Upstream rate = 12121 Kbps, Downstream rate = 50128 Kbps
Bearer: 0, Upstream rate = 12015 Kbps, Downstream rate = 39617 Kbps

Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 6.1 6.1
Attn(dB): 19.6 0.0
Pwr(dBm): 13.4 6.7
VDSL2 framing
Bearer 0
MSGc: 15 20
B: 25 238
M: 1 1
T: 64 31
R: 10 16
S: 0.0209 0.6330
L: 13792 3223
D: 2803 1
I: 36 255
N: 36 255
Counters
Bearer 0
OHF: 28975885 94221
OHFErr: 22 1
RS: 96107058 404081
RSCorr: 226629 2
RSUnCorr: 105 0

Bearer 0
HEC: 14 0
OCD: 1 0
LCD: 1 0
Total Cells: 887550679 0
Data Cells: 126460610 0
Drop Cells: 0
Bit Errors: 0 0

ES: 71 7948
SES: 40 93
UAS: 115 251579
AS: 68033

Bearer 0
INP: 8.00 0.00
INPRein: 0.00 0.00
delay: 14 0
PER: 2.34 9.84
OR: 71.55 21.11
AgR: 39688.52 12036.07

Bitswap: 46829/47149 1/1

Total time = 1 days 1 hours 38 min 30 sec
FEC: 1119500 64
CRC: 17099 3
ES: 71 7948
SES: 40 93
UAS: 115 251579
LOS: 4 3
LOF: 26 3
LOM: 18 0
Latest 15 minutes time = 8 min 30 sec
FEC: 935 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 15 minutes time = 15 min 0 sec
FEC: 4227 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 1 day time = 1 hours 38 min 30 sec
FEC: 17256 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 1 day time = 24 hours 0 sec
FEC: 534737 61
CRC: 9876 3
ES: 40 2652
SES: 23 31
UAS: 47 83903
LOS: 3 1
LOF: 13 1
LOM: 11 0
Since Link time = 18 hours 53 min 53 sec
FEC: 226629 2
CRC: 22 1
ES: 7 2652
SES: 0 31
UAS: 0 83878
LOS: 0 1
LOF: 0 1
LOM: 0 0

Stats recorded 27 Apr 2020 17:58:47

DSLAM type / SW version: IFTN:0xd086 (208.134) / v0xd086
Modem/router firmware: AnnexA version – A2pv6C038m.d24j
DSL mode: VDSL2 Profile 17a
Status: Showtime
Uptime: 18 hours 56 min 53 sec
Resyncs: 0 (since 27 Apr 2020 17:52:13)

Downstream Upstream
Line attenuation (dB): 19.6 0.0
Signal attenuation (dB): Not available on VDSL2
Connection speed (kbps): 39617 12015
SNR margin (dB): 6.3 6.1
Power (dBm): 13.4 6.7
Interleave depth: 2803 1
INP: 8.00 0
G.INP: Not enabled Not enabled
Vectoring status: 5 (VECT_UNCONFIGURED)

RSCorr/RS (%): 0.1767 0.0001
RSUnCorr/RS (%): 0.0001 0.0000
ES/hour: 8.57 0

Attachments:

1. 

   QLN-graph-2020-04-27-175759.png
   

You need to login in order to vote

[Mrk26]

Only FEC still bit high, rest looks O.K.

However as your DLM card is on different fw than mime you may get fastpath, from this what I realised the one you are on is “more user friendly”.

You need to login in order to vote

[Bully]

UK Sentinel wrote:

Bully wrote:

Is the Below WAN setup correct?

See my WAN settings for comparison, only differences is (mine are all default) my Bridge Type is IP_Bridged and you have 802.1p enabled and I do not . I think your Bridge Type should change if your are having problems but not so sure regarding 802.1p as that is QoS and unsure if you have set this up. ? Mine seems to work well and no complaints from family as yet

Just after I took the above stats I matched my settings to yours.  It did not loose connection nor did it ask to reboot  and I did not do a manually reboot.

You need to login in order to vote

[UK Sentinel]

A reboot is probable required at some point, how’s the modem generally, r u happy with increased bandwidth, any lag on gaming, is modem still getting to hot etc ?

In a completely sane world, madness is the only freedom (J.G.Ballard).

You need to login in order to vote

[Bully]

UK Sentinel wrote:

A reboot is probable required at some point, how’s the modem generally, r u happy with increased bandwidth, any lag on gaming, is modem still getting to hot etc ?

 

Modem is not getting too hot now. I am happy with the increased bandwidth, and is pretty solid.  Wish i could access stats through router.  Was thinking about connecting lan 2 to router to access stats that way, but had heard it can cause disconnects?  Ping is higher than it use to be at about 25ms.  Not too much lag during gaming, hard to connect to servers under 50ms on COD MW 2019 on xbox one X due to higher demand cause of lock down.

You need to login in order to vote

[Mrk26]

It should work perfectly fine on two cables, I have it like that on my old eci modem for months, no issues at all. On other forum people used HG612 on two cables for ages and I didn’t heard that this was caused issues.

@Uk Sentinel

How is yours connected?

You need to login in order to vote

[UK Sentinel]

@Mrk26. mine just has single ethernet between Modem LAN1 and Router WAN Port, I have not set up second Cable for stats via router and I am only testing currently, and practising KIS (Keep it Simple)

@Bully – Yes extra Bandwidth is very positive and hopefully in fastpath will kick in if errors are low enough ?

In a completely sane world, madness is the only freedom (J.G.Ballard).

You need to login in order to vote

[Mrk26]

UK Sentinel wrote:

@Mrk26. mine just has single ethernet between Modem LAN1 and Router WAN Port, I have not set up second Cable for stats via router and I am only testing currently, and practising KIS (Keep it Simple)

I don’t believe in such thing, if something working, it should work with full potential, disappointed now, though you will fully unleash the beast 😂😂

You need to login in order to vote

[UK Sentinel]

Attachments:

1. 

   minion.jpg
   

In a completely sane world, madness is the only freedom (J.G.Ballard).

You need to login in order to vote

[Mrk26]

UK Sentinel wrote:

https://www.google.co.uk/imgres?imgurl=https%3A%2F%2Fthefunnybeaver.com%2Fwp-content%2Fuploads%2F2017%2F08%2Fminion-better.jpg&imgrefurl=https%3A%2F%2Fthefunnybeaver.com%2F33-funniest-minion-quotes-pictures%2F&tbnid=rbnH1IZ9IsPP0M&vet=12ahUKEwiE5_66novpAhVKw4UKHRCNDzsQMygbegQIARA3..i&docid=qAXsaDJPqY3erM&w=404&h=368&q=work%20and%20effort%20funny%20quotes%20minion&ved=2ahUKEwiE5_66novpAhVKw4UKHRCNDzsQMygbegQIARA3

Love it

You need to login in order to vote

[Bully]

Todays Stats –

xdslcmd info –stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 6
Last initialization procedure status: 0
Max: Upstream rate = 12271 Kbps, Downstream rate = 50356 Kbps
Bearer: 0, Upstream rate = 12015 Kbps, Downstream rate = 39617 Kbps

Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 6.2 6.3
Attn(dB): 19.6 0.0
Pwr(dBm): 13.4 6.7
VDSL2 framing
Bearer 0
MSGc: 15 20
B: 25 238
M: 1 1
T: 64 31
R: 10 16
S: 0.0209 0.6330
L: 13792 3223
D: 2803 1
I: 36 255
N: 36 255
Counters
Bearer 0
OHF: 65834624 364801
OHFErr: 77 2
RS: 3723920158 1790063
RSCorr: 539878 14
RSUnCorr: 1578 0

Bearer 0
HEC: 222 0
OCD: 5 0
LCD: 5 0
Total Cells: 3185027118 0
Data Cells: 551275815 0
Drop Cells: 0
Bit Errors: 0 0

ES: 80 7949
SES: 40 93
UAS: 115 251579
AS: 154573

Bearer 0
INP: 8.00 0.00
INPRein: 0.00 0.00
delay: 14 0
PER: 2.34 9.84
OR: 71.55 21.11
AgR: 39688.52 12036.07

Bitswap: 106505/107170 18/19

Total time = 1 days 1 hours 40 min 50 sec
FEC: 1432749 76
CRC: 17154 4
ES: 80 7949
SES: 40 93
UAS: 115 251579
LOS: 4 3
LOF: 26 3
LOM: 18 0
Latest 15 minutes time = 10 min 50 sec
FEC: 4767 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 15 minutes time = 15 min 0 sec
FEC: 5110 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 1 day time = 1 hours 40 min 50 sec
FEC: 57266 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Previous 1 day time = 24 hours 0 sec
FEC: 273239 12
CRC: 55 1
ES: 9 1
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Since Link time = 1 days 18 hours 56 min 13 sec
FEC: 539878 14
CRC: 77 2
ES: 16 2653
SES: 0 31
UAS: 0 83878
LOS: 0 1
LOF: 0 1
LOM: 0 0

Stats recorded 28 Apr 2020 17:58:39

DSLAM type / SW version: IFTN:0xd086 (208.134) / v0xd086
Modem/router firmware: AnnexA version – A2pv6C038m.d24j
DSL mode: VDSL2 Profile 17a
Status: Showtime
Uptime: 1 day 18 hours 56 min 43 sec
Resyncs: 0 (since 28 Apr 2020 17:56:36)

Downstream Upstream
Line attenuation (dB): 19.6 0.0
Signal attenuation (dB): Not available on VDSL2
Connection speed (kbps): 39617 12015
SNR margin (dB): 6.2 6.2
Power (dBm): 13.4 6.7
Interleave depth: 2803 1
INP: 8.00 0
G.INP: Not enabled Not enabled
Vectoring status: 5 (VECT_UNCONFIGURED)

RSCorr/RS (%): 0.0145 0.0007
RSUnCorr/RS (%): 0.0000 0.0000
ES/hour: 0 0

You need to login in order to vote

[Author]

Posts