RT-AC86U 384.16 Hi, I updated to the latest Merlin firmware this morning (about 9 am) and since doing so my NE CRC count has gone up to 326598 over 5 hours. ...

[Bully]

Upgraded router merlin fw to 384.17 this morning, did a factory reset, and connected HG612 lan2 to router.  I can access modem through router now.

 

Seen this in router stats, getting this log every 3 seconds or so – May 2 09:52:09 kernel: br0: received packet on eth1 with own address as source address ?

 

Today’s stats –

xdslcmd info –stats
xdslcmd: ADSL driver and PHY status
Status: Showtime
Retrain Reason: 0
Last initialization procedure status: 0
Max: Upstream rate = 12381 Kbps, Downstream rate = 51076 Kbps
Bearer: 0, Upstream rate = 12280 Kbps, Downstream rate = 39994 Kbps

Link Power State: L0
Mode: VDSL2 Annex B
VDSL2 Profile: Profile 17a
TPS-TC: PTM Mode(0x0)
Trellis: U:ON /D:ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 6.9 6.1
Attn(dB): 19.5 0.0
Pwr(dBm): 13.4 6.8
VDSL2 framing
Bearer 0
MSGc: 18 21
B: 31 238
M: 1 1
T: 64 22
R: 10 16
S: 0.0255 0.6193
L: 13200 3294
D: 1283 1
I: 42 255
N: 42 255
Counters
Bearer 0
OHF: 244576 58653
OHFErr: 0 0
RS: 93762310 3869246
RSCorr: 517 0
RSUnCorr: 0 0

Bearer 0
HEC: 0 0
OCD: 0 0
LCD: 0 0
Total Cells: 46091927 0
Data Cells: 17595135 0
Drop Cells: 0
Bit Errors: 0 0

ES: 0 2655
SES: 0 31
UAS: 25 84362
AS: 601

Bearer 0
INP: 3.50 0.00
INPRein: 0.00 0.00
delay: 8 0
PER: 2.45 10.25
OR: 78.26 21.05
AgR: 40072.04 12301.21

Bitswap: 393/396 0/0

Total time = 10 min 26 sec
FEC: 517 0
CRC: 0 0
ES: 0 2655
SES: 0 31
UAS: 25 84362
LOS: 0 1
LOF: 0 1
LOM: 0 0
Latest 15 minutes time = 10 min 26 sec
FEC: 517 0
CRC: 0 0
ES: 0 2655
SES: 0 31
UAS: 25 84362
LOS: 0 1
LOF: 0 1
LOM: 0 0
Previous 15 minutes time = 0 sec
FEC: 0 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Latest 1 day time = 10 min 26 sec
FEC: 517 0
CRC: 0 0
ES: 0 2655
SES: 0 31
UAS: 25 84362
LOS: 0 1
LOF: 0 1
LOM: 0 0
Previous 1 day time = 0 sec
FEC: 0 0
CRC: 0 0
ES: 0 0
SES: 0 0
UAS: 0 0
LOS: 0 0
LOF: 0 0
LOM: 0 0
Since Link time = 9 min 59 sec
FEC: 517 0
CRC: 0 0
ES: 0 2655
SES: 0 31
UAS: 0 84337
LOS: 0 1
LOF: 0 1
LOM: 0 0

Stats recorded 02 May 2020 09:52:20

DSLAM type / SW version: IFTN:0xd086 (208.134) / v0xd086
Modem/router firmware: AnnexA version – A2pv6C038m.d24j
DSL mode: VDSL2 Profile 17a
Status: Showtime
Uptime: 0 hour 12 min 31 sec
Resyncs: 0 (since 02 May 2020 09:49:47)

Downstream Upstream
Line attenuation (dB): 19.5 0.0
Signal attenuation (dB): Not available on VDSL2
Connection speed (kbps): 39994 12280
SNR margin (dB): 6.9 6.1
Power (dBm): 13.4 6.8
Interleave depth: 1283 1
INP: 3.50 0
G.INP: Not enabled Not enabled
Vectoring status: 5 (VECT_UNCONFIGURED)

RSCorr/RS (%): 0.0005 0.0000
RSUnCorr/RS (%): 0.0000 0.0000
ES/hour: 0 0

You need to login in order to vote

[Mrk26]

Check if modem hold connection, these stats are only from 10 mins, unless you reboot modem as well with router.

You need to login in order to vote

[Bully]

ARGGHHHHH – Cant access my router now, via its lan ip.  Can access it via router.asus. com.

You need to login in order to vote

[Mrk26]

How did you configure router? 🤔

With two cable option you should have automatic wan IP, you can change dns if you want. To give modem ip like on vigor don’t give you any benefits, but can cause issues with two cables option.

You need to login in order to vote

[Bully]

Mrk26 wrote:

How did you configure router? 🤔 With two cable option you should have automatic wan IP, you can change dns if you want. To give modem ip like on vigor don’t give you any benefits, but can cause issues with two cables option.

 

Automatic wan ip on router?

You need to login in order to vote

[Mrk26]

Yes, and make sure HG612 have different IP on lan than asus but they must be in same IP group eg. 192.168.1.xx.

You need to login in order to vote

[Bully]

I have configured the modem on 192.168.1.XX, the router is on 192.168.0.XX, i have configured router wan to modem lan.

You need to login in order to vote

[UK Sentinel]

@bully is using single cable option I think ?

In a completely sane world, madness is the only freedom (J.G.Ballard).

You need to login in order to vote

[Bully]

UK Sentinel wrote:

@bully is using single cable option I think ?

 

2 cable option as of this morning.

You need to login in order to vote

[Bully]

Settings –

 

Attachments:

1. 

   HG612-LAN-2020-05-02-124817.png
   

2. 

   Asus-WAN-2020-05-02-125257.png
   

3. 

   Asus-LAN-2020-05-02-125516.png
   

You need to login in order to vote

[Mrk26]

When I used eci modem with two cables all was configured like that:

Modem – lan 192.168.1.2

Subnet mask 255.255.255.0

Router – 192.168.1.1

Subnet mask 255.255.255.0

Wan IP automatically, as you access modem through lan port.

 

You need to login in order to vote

[Mrk26]

Also as mentioned earlier setup in lan in router start address from eg 192.168.1.6 so router will not assign IP dedicated for modem lan to other device. Then you should see modem ip eg. 192.168.1.2 on your connected devices list.

You need to login in order to vote

[Bully]

Set wan IP on router to auto, i have internet but now cannot access modem.

 

***EDIT*** – CHANGED BACK TO MANUAL AND I CAN NOW ACCESS MODEM.

You need to login in order to vote

[UK Sentinel]

Bully wrote:

UK Sentinel wrote:

@bully is using single cable option I think ?

2 cable option as of this morning.

If you are then that will fail, @Mrk26 option should work

In a completely sane world, madness is the only freedom (J.G.Ballard).

You need to login in order to vote

[Bully]

See my edited post above

You need to login in order to vote

[Author]

Posts