[Bully]

To be fair my Draytek has been solid now for some months.  I found a forum stating that the Draytek has vectoring enabled and can cause an unstable line, I disabled this via a CLI command and it has been rock solid till now.

I cant remember if i tried my HG612 either lol.

I have also read somewhere the quickest way to reduce interleaving is to cap the line via a CLI command, not that i know what that command is on the Draytek.

You need to login in order to vote

[Bully]

Right, I reverted back to 384.15, this has made no difference after the flash and a power down for 15 mins.  It must just of been a coincidence.

My interleave depth has gone up over night –

DS Actual Rate          : 34416000 bps   US Actual Rate       : 10666000 bps
DS Attainable Rate      : 42690000 bps   US Attainable Rate   : 10841414 bps
DS Path Mode            :  Interleave    US Path Mode         :        Fast
DS Interleave Depth     :     1441       US Interleave Depth  :        1
NE Current Attenuation  :       20 dB    Cur SNR Margin       :        5  dB
DS actual PSD           :     6. 4 dB    US actual PSD        :    12. 9  dB
NE CRC Count            :    48488       FE CRC Count         :     4012
NE ES Count             :     1411       FE  ES Count         :     2626

These stats are 15 minutes after the 15 minute power down of router and modem –   NE CRC Count :  48488  FE CRC Count   :   4012 NE ES Count : 1411.  The DS Actual Rate of 34416000 bps has dropped over night from 40251000 bps.

 

Is there anything I can do to get the errors down and my interleave depth down in way of snr or speed capping or should I just leave things alone?

You need to login in order to vote

[Bully]

yeah that’s what I was thinking.  Thanks for the help.  I will let you know how it goes tomorrow.

You need to login in order to vote

[Bully]

Turned off router and modem at 18.10, it has made no difference  –

stats after 40 mins

NE CRC Count            :    73740       FE CRC Count         :     4011
NE ES Count             :     2630       FE  ES Count         :     2625

You need to login in order to vote

[Bully]

That sounds like a plan

You need to login in order to vote

[Bully]

Ok,  Will have to be after midnight or first thing in the morning, don’t want to upset anyone in the house, and with the lock down i cant escape the carnage .  I will let you know how it goes.

You need to login in order to vote

[Bully]

Nope, cant see anything.

 

Very strange, gone up to 449564 since starting this thread.

You need to login in order to vote

[Bully]

Yeah sorry Draytek Vigor 130.

You need to login in order to vote

[Bully]

UK Sentinel wrote:

Sorry, just read the instruction and LAN port 2 is the one described / needed Firmware look good

 

oh dear, I have tried flashing it 10 + times and can’t access the gui.

You need to login in order to vote

[Bully]

UK Sentinel wrote:

Bully wrote:

UK Sentinel wrote:

I updated my HG612 the other day after talking with you and manged it, if accessing HG612, you have to change IP address of Connection PC/Laptop to say 192.168.1.9 and plug ethernet cable into LAN port 2 to gain access Access to UI is via http://192.168.1.1

I have set laptop to 192.168.1.100, and connecting to lan port 2 on HG612 but no joy.

I believe you may have to flash the firmware several times in order to get it to stick, which firmware did you use in the end ? When flashing new firmware, connect laptop to Lan 1 port

Will give lan 1 a try.

Using – bcm96368MVWG_fs_kernel_HG612V100R001C01B030SP08_webgui

You need to login in order to vote

[Bully]

UK Sentinel wrote:

I updated my HG612 the other day after talking with you and manged it, if accessing HG612, you have to change IP address of Connection PC/Laptop to say 192.168.1.9 and plug ethernet cable into LAN port 2 to gain access Access to UI is via http://192.168.1.1

 

I have set laptop to 192.168.1.100, and connecting to lan port 2 on HG612 but no joy.

You need to login in order to vote

[Bully]

Decided to try my HG612 3B, I tried to update the firmware to access the GUI (as per the Kitz forum), I can start the update process but when complete it wont allow me to access the gui, nor can I ping its ip address?

You need to login in order to vote

[Bully]

No not yet

You need to login in order to vote

[Bully]

I really cant remember, its my age you know

You need to login in order to vote

[Bully]

BT Engineer came today, tested line and found no faults, he reset line profile and i am now getting these stats –

Data rate : 11.795 Mbps / 45.218 Mbps

Maximum data rate : 11.878 Mbps / 45.775 Mbps

Noise margin : 6.1 / 6.1

Line attenuation : 9.9 / 18.9

Signal attenuation : 9.8 / 24.0

You need to login in order to vote

[Author]

Posts