[SH]

Huawei will be allowed to do business with U.S. companies again

https://www.androidauthority.com/breaking-huawei-allowed-to-do-business-with-us-companies-again-1004260/

You need to login in order to vote

[SH]

you can use Ping plotter and ping your ISP gateway IP or any local site ( if it accept ICMP pings )  to monitor your connection over time ……. to see errors or packet drops or sudden spikes in ping on hoops

https://www.pingplotter.com/

your modem is in bridge mode or modem is dialing the connection ?

way back i used to have issue on my VMG1312-B10A … where enabling SRA used to … give sudden burst in CRC than connection re-synchs and disabling it fix the issue ………… but not sure if SRA is used there or not

 

You need to login in order to vote

[SH]

UK Sentinel wrote:

What modem/fibre box is your AX-88U connected to ? Edit: I see ‘Static IP’ Stock ASUSWRT does not and most likely never will offer this option, RMerlin (ASUSWRT-Merlin) does offer this and mine (RT-AC86U – ASUSWRT-Merlin) is set to 1500 also for Static or Dynamic IP running a dual ipv4 /v6 stack 😉 or via Telnet/SSH try the cmd ( ifconfig eth0 mtu 1472 ) remove brackets and see if this helps ? a reboot will remove this value, but good for testing on standard ASUSWRT. Or if you are you getting fragmentation try the following from PC: ping [site] -f -l 1472 and change value until you stop receiving the Fragmentation error message (then add + 28 for final MTU Value for PPPoE Connection on router). Hopefully CMDs will work but ASUSWRT underlying language is always changing between models ;-( https://asuswrt.lostrealm.ca

Hey Thank’s , I’m trying ASUSWRT-Merlin Firmware ………………. lets see how its goes ……

You need to login in order to vote

[SH]

I know about PPPoE , but when you use Static IP there is no option to configure MTU or MRU ( default should be 1500 when static ip is set )

default MTU used on ISP Modem for IPv6 is 1472 …, that’s why i was asking if there is any way to optimize IPv6 MTU .

i wonder if ASUS could add this option to change MTU value in IPv6 settings in future ?

i got AX-88U

You need to login in order to vote

[SH]

I apologize.. i don’t own DSL-88U, but have other ASUS routers

No , i have IPv6 disabled , when i had it enabled … i used to have issue with slow browsing …even if IPv6 ICMP was reachable …….

you can try testing by disabling  IPv6 Firewall + allow Respond ICMP Echo (ping) Request from WAN and see if it works …………… but most likely it’s Asus firmware filtering it

i would like to ask @UK Sentinel …. is there any way to configure IPv6 MTU in GUI ? or what is the default value used for IPv6 MTU on ASUS router ?  because some IPv6 test site show Packet too Big.

Attachments:

1. 

   ipv6.png
   

You need to login in order to vote

[SH]

which device your running test ?

i used to have this issue in past on windows where windows firewall was blocking IPv6 ICMP Echo Request  , you can try this command ….run as admin ………….. and see if works …

netsh advfirewall firewall add rule name=”ICMPv6 echo request” protocol=icmpv6:8,any dir=in action=allow

You need to login in order to vote

[SH]

speedtest fix themselves

You need to login in order to vote

[SH]

this issue have been fixed …. thank you :)

You need to login in order to vote

[SH]

yeah , need somebody on 250+ upload range ……….
i have tested it on 2 different connection on different location .. but not able to pinpoint whats going on

You need to login in order to vote

[SH]

it’s personal opinion , but feels like it’s all related to trade war between USA and China ( i could be wrong )  ………. if US GOV Administration gets what they want ..they will be happy i guess ? .. through Huge Loss for huawei ……..

but i wonder ? if huawei shift brand under different name , transfer their assets  and reallocate to different place/jurisdiction does it going  to work for them ?

Liked by:

You need to login in order to vote

[SH]

Hey,

How do you see Huawei ban ? does it going to effect products like existing routers ,modem , ISP DSLAM and other various network equipment that are supplied by Huawei ? ……. does it mean no support for existing products if bugs are found later on them from chip manufacturer ? ……..because Qualcomm and Broadcom are also planning to cut off their collaboration with Huawei

You need to login in order to vote

[SH]

Samsung would be great choice
hahah .. dishwasher engineer would be more better than Samsung :D  ( new experience  )

You need to login in order to vote

[SH]

I would really choose local or international brand depending on ->  good customer base , good after purchase customer support , and competitive pricing of items.

 

i can’t say about specific item …….since every company are best in some areas ….. through i have used Bosch Professional tools and many Samsung electronics ( TV,Phones ,Refrigerator, Washing Machine)    they both are good … i hardly needed any after customer support …..for those items in last 15 years

i have not used anything related to Miele so i can’t say

You need to login in order to vote

[SH]

yeah i think so it’s broken for now
.. not sure when new firmware going to release .. but i don’t think …..Netgear/Netduma will give any priority to fix ipv6 issue .. unless some ISP start giving out ipv6 only address …and many user start reaching out netgear about this issue

You need to login in order to vote

[SH]

i have not tested it with QOS disabled yet to see if it works , but with QOS enabled it lags  ……… i suspect ….it’s more to do with netgear implementation of IPV6 ………

also i have noticed …

that during 6to4 mode … web browser is not using IPV6 to visit website …. but lags , ( few ipv6 test website even failed to detect there is ipv6 )

but during PPPoE  mode (Native ipv6 address ) … web browser was using …IPV6 and it still lags

You need to login in order to vote

[Author]

Posts