[Mrk26]

No problem, if there’s nothing change tonight try to put cap again on your line.

You need to login in order to vote

[Mrk26]

If you can, post stats in the morning.

You need to login in order to vote

[Mrk26]

You get lot of FEC errors last 10h, did you changed anything? These are like 3 times worse than previous stats. Your average from 120k FEC errors within 24h will go up to 1mln now. I was full of hope that you may get fastpath tonight, but now I’m not sure. Try to unplug telephone from filtered faceplate and check stats after few hours.

You need to login in order to vote

[Mrk26]

When you switched off your hg612, your cap was removed.

You need to login in order to vote

[Mrk26]

And it’s only 2nd day since last DLM intervention

You need to login in order to vote

[Mrk26]

That distance shouldn’t be a problem with g.inp and 3db profile

Hope you won’t have to wait to long for g.inp to kick in.

 

Edit.

Grammar corrections due to terrible mobile dictionary predictions 😡😡

You need to login in order to vote

[Mrk26]

Looking on previous stats I think with 3db profile you should be close to 80Mb/s.

You need to login in order to vote

[Mrk26]

Another 5 full days, with good wind 3

You need to login in order to vote

[Mrk26]

Little steps

Snr on 7db now and interleave delay down from 15ms to 8ms now. So there is a progress

You need to login in order to vote

[Mrk26]

That’s 5th day, let’s hope something will move tonight

You need to login in order to vote

[Mrk26]

Unfortunately UK is not on the top with broadband technologies (at least FTTC) , and all issues came up with poor solutions, mixed equipment etc., for example aluminium cables from 70s never been replaced untill cause serious connection issues. That’s why we have to use faceplates which have build in filters to clear up signal from noise caused by crosstalk (vectoring only on few Huawei cabinets, on eci not available as current cards don’t support) and poor wiring, and they do really good job on that. Most cabinets in UK are eci where only in UK they didn’t support g.inp (is on another testing phase now)  but same cabinets (I think in Izrael) support g.inp already from few years. Everywhere in Europe broadband working much better, in UK is big woohoo about gigabit fibre where in rest of Europe that’s nothing new. But untill we all go for full fibre when available we have to suffer and do our best to get what we can from our broadband.

You need to login in order to vote

[Mrk26]

Looking forward to see how stats will looks like on new socket

You need to login in order to vote

[Mrk26]

Bully wrote:

Yeah, I was getting worried as the errors seem to have increased a bit. SRA and G.Vector is still off. vdsl optn status trellis [US] = ON, [DS] = ON. bitswap [US] = 0, [DS] = 0. [0: default(ON), 1: ON, 2: OFF] sra [US] = 2, [DS] = 2. [0: default(=3), 2: OFF, 3: ON , 4: DYNAMIC_SOS] retx [US] = ON, [DS] = ON. vpcs 0xff aelem ON G.Vector OFF @uk-sentinel – has your gfast faceplate turned up yet?

If nothing change by Tuesday you can try to increase snr on downstream, that should keep your line with low amount of errors.

You need to login in order to vote

[Mrk26]

With this high interleave amount of errors still looking not bad.

You need to login in order to vote

[Mrk26]

Probably @Bully stuck on the beach somewhere

You need to login in order to vote

[Author]

Posts