[Mrk26]

Just a quick update.

Vigor 2760 survived whole 24h and still going on fastpath. Must be then too many disconnections (due to setup) what pushed dlm to put my line on absolute interleave.

You need to login in order to vote

[Mrk26]

At least is sorted 👍

I don’t have any reason to think or suspect that something may be wrong with my line, so I blame myself at the moment. I don’t even think about to reduce snr (tiny – 0.8db) to get full speed as I spoke with people on ee community forum regarding g.inp, unfortunately they wasn’t able yet to confirm if ee opt in for trial but if they will they will try to push me in to the trial.

You need to login in order to vote

[Mrk26]

After I eliminate aluminum extension in my house I don’t have any issues with line at all. Also bear in mind that old bt eci modem was constantly on fastpath for three months. I remember doing quite line test in past (before sorted aluminum extension) and line was quite. I personally think that there was too many disconnections with vigor before I managed to setup that damn thing properly 😅. Will see tomorrow morning. Based on last experience I didn’t have to wait long for dlm with vigor on my line 😜.

I think is worth to mention that on my line lantiq based modem have slighty lower latency comparing to broadcom based modems, also I realise that even with QOS set (of course individually to line speed) on vigor I have a lot less bufferbloat than on zyxel. I like zyxel for abilities to maintain line in need, but other than that I’m struggle to force myself to use it on daily basis.

You need to login in order to vote

[Mrk26]

Probably best record (so far) on my ECI cabinet. After full three days fastpath was enabled on upstream, after another three days fastpath kicked in on downstream. Zyxel modem sync with just under 75Mb/s but throughput seems to be very poor, achievable speed only 61Mb/s where ip profile is 69. Time for vigor, will see if it don’t mess up this time.

You need to login in order to vote

[Mrk26]

Hi @Cozak

Dod you tried latest alpha 384.16 build, or even latest asus 3.0.0.4.384.7977, wonder if issues with Wi-Fi still there? 🤔

You need to login in order to vote

[Mrk26]

That’s what probably confuse me.

You need to login in order to vote

[Mrk26]

Yes, Broadcom based modems are best to stabilise line, but for long term use… Noooo 😂

You need to login in order to vote

[Mrk26]

After few out of my control disconnections (wife on duty 😂) I managed to keep zyxel connected for three days constantly, today morning checked and dlm resync after 1AM and put fastpatch on upstream 😁. If old scheme still works, after 5 days I should be back on fastpatch on downstream. Was thinking if won’t be worth put now vigor and see if fastpatch won’t kick on it, I only keep small cap on downstream now 🤔

You need to login in order to vote

[Mrk26]

It’s difficult to be busy in wonderful weather like this 😂😂

You need to login in order to vote

[Mrk26]

UK Sentinel wrote:

We have all been there, I had the DrayTeK 130 in for ages and G.inp would not kick in, I finally plugged in my Fritz!Box 3490 and two days later G.inp was working. for me it appears that most DSL chipsets keeps FastPath/G.inp enabled, but only certain ones are suitable to re-enable a service and/or the firmware also ? DrayTek 130 = Lantiq (VR9) Fritz!Box 3490 = Lantiq (VRX288) https://openwrt.org/docs/techref/hardware/soc/soc.lantiq

I was looking into this and looks like vigor 2760 is on same chipset as your fritzbox…

Wondering if they didn’t mess up with fw? 🤔

You need to login in order to vote

[Mrk26]

Wish I could….

I will have to change house to get FTTP but is not worth, love my current one

I use opportunity that most of my family go out and put in place zyxel, capped straightaway to 60/15Mbs and will wait for magic to start working.

 

edit

Was actually smoother than I expected, configured zyxel to use on one cable as well, just changed ip to slightly different than vigor

You need to login in order to vote

[Mrk26]

Well previously I was on asus dsl-ac88u and fastpatch didn’t kicked until I capped speed. So not sure if modem abilities play here on my line. For some reason cabinet stuck on these settings until it get kick.

You need to login in order to vote

[Mrk26]

I keep thinking about this, it’s just annoying because I setup all to work properly with vigor now will have to change back configuration for zyxel. Instead of waiting for two weeks I may be able to achieve something earlier. Just need to wait for family to go out so I can play with it in peace.

You need to login in order to vote

[Mrk26]

This is exactly the one I read. I will give one more week for vigor and then will play with zyxel. The thing is that last time when I had situation like this nothing didn’t changed for 15 days until I capped speed.. Will see.

You need to login in order to vote

[Mrk26]

Eci, and I don’t have idea what’s going on . I only got some FEC errors like 30k per day, no other errors. I wonder if BT didn’t change anything on cabinet, apparently they going to launch g.inp trial again in March for ECI cabinets (not necessary mine).

You need to login in order to vote

[Author]

Posts